收藏本站
VISHAY SILICONIX
TrenchFET ? Power MOSFETs
Application Note 808
Mounting LITTLE FOOT ? , SO-8 Power MOSFETs
Wharton McDaniel
0.2 88
Surface-mounted LITTLE FOOT power MOSFETs use
integrated circuit and small-signal packages which have
7.3
been been modified to provide the heat transfer capabilities
required by power devices. Leadframe materials and
design, molding compounds, and die attach materials have
been changed, while the footprint of the packages remains
the same.
See Application Note 826, Recommended Minimum Pad
Patterns With Outline Drawing Access for Vishay Siliconix
0.050
1.27
0.027
0.69
0.07 8
1.9 8
0.2
5.07
0.0 88
2.25
0.0 88
2.25
MOSFETs, ( http://www.vishay.com/ppg?72286 ), for the
basis of the pad design for a LITTLE FOOT SO-8 power
MOSFET. In converting this recommended minimum pad
to the pad set for a power MOSFET, designers must make
two connections: an electrical connection and a thermal
connection, to draw heat away from the package.
In the case of the SO-8 package, the thermal connections
are very simple. Pins 5, 6, 7, and 8 are the drain of the
MOSFET for a single MOSFET package and are connected
together. In a dual package, pins 5 and 6 are one drain, and
pins 7 and 8 are the other drain. For a small-signal device or
integrated circuit, typical connections would be made with
traces that are 0.020 inches wide. Since the drain pins serve
the additional function of providing the thermal connection
to the package, this level of connection is inadequate. The
total cross section of the copper may be adequate to carry
the current required for the application, but it presents a
large thermal impedance. Also, heat spreads in a circular
fashion from the heat source. In this case the drain pins are
the heat sources when looking at heat spread on the PC
board.
0.2 88
7.3
0.050
1.27
0.196
5.0
0.027
0.69
Figure 2. Dual MOSFET SO-8 Pad Pattern
With Copper Spreading
The minimum recommended pad patterns for the
single-MOSFET SO-8 with copper spreading (Figure 1) and
dual-MOSFET SO-8 with copper spreading (Figure 2) show
the starting point for utilizing the board area available for the
heat-spreading copper. To create this pattern, a plane of
copper overlies the drain pins. The copper plane connects
the drain pins electrically, but more importantly provides
planar copper to draw heat from the drain leads and start the
process of spreading the heat so it can be dissipated into the
ambient air. These patterns use all the available area
underneath the body for this purpose.
Since surface-mounted packages are small, and reflow
soldering is the most common way in which these are
affixed to the PC board, “thermal” connections from the
planar copper to the pads have not been used. Even if
additional planar copper area is used, there should be no
problems in the soldering process. The actual solder
connections are defined by the solder mask openings. By
combining the basic footprint with the copper plane on the
drain pins, the solder mask generation occurs automatically.
A final item to keep in mind is the width of the power traces.
The absolute minimum power trace width must be
determined by the amount of current it has to carry. For
0.07 8
1.9 8
0.2
5.07
thermal reasons, this minimum width should be at least
0.020 inches. The use of wide traces connected to the drain
Figure 1. Single MOSFET SO-8 Pad
Pattern With Copper Spreading
Document Number: 70740
Revision: 18-Jun-07
plane provides a low impedance path for heat to move away
from the device.
www.vishay.com
1
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*
相关PDF资料
SI4435DY MOSFET P-CH 30V 8.8A 8-SOIC
SI4435DY MOSFET P-CH 30V 8A 8-SOIC
SI4448DY-T1-GE3 MOSFET N-CH 12V 50A 8-SOIC
SI4455-B1A-FM IC EZRADIO FM TRANSCEIVER SI4355
SI4462DY-T1-GE3 MOSFET N-CH 200V 1.15A 8-SOIC
SI4463-915-DK KIT DEV WIRELESS SI4463 915MHZ
SI4465ADY-T1-GE3 MOSFET P-CH 8V 13.7A 8SOIC
SI4466DY-T1-GE3 MOSFET N-CH 20V 9.5A 8-SOIC
相关代理商/技术参数
SI4435DDY-T1-E3 制造商:Vishay Siliconix 功能描述:P CHANNEL MOSFET -30V 11.4A SOIC
SI4435DDY-T1-GE3 功能描述:MOSFET 30V 11.4A 5.0W 24mohm @ 10V RoHS:否 制造商:STMicroelectronics 晶体管极性:N-Channel 汲极/源极击穿电压:650 V 闸/源击穿电压:25 V 漏极连续电流:130 A 电阻汲极/源极 RDS（导通）:0.014 Ohms 配置:Single 最大工作温度: 安装风格:Through Hole 封装 / 箱体:Max247 封装:Tube
SI4435DY 功能描述:MOSFET 30V SinGLE P-Ch RoHS:否 制造商:STMicroelectronics 晶体管极性:N-Channel 汲极/源极击穿电压:650 V 闸/源击穿电压:25 V 漏极连续电流:130 A 电阻汲极/源极 RDS（导通）:0.014 Ohms 配置:Single 最大工作温度: 安装风格:Through Hole 封装 / 箱体:Max247 封装:Tube
SI4435DY 制造商:Fairchild Semiconductor Corporation 功能描述:TRANSISTOR MOSFET 制造商:Fairchild Semiconductor Corporation 功能描述:TRANSISTOR, MOSFET
SI4435DY 制造商:Fairchild Semiconductor Corporation 功能描述:MOSFET TRANSISTOR ROHS COMPLIANT:NO
SI4435DY_Q 功能描述:MOSFET 30V SinGLE P-Ch RoHS:否 制造商:STMicroelectronics 晶体管极性:N-Channel 汲极/源极击穿电压:650 V 闸/源击穿电压:25 V 漏极连续电流:130 A 电阻汲极/源极 RDS（导通）:0.014 Ohms 配置:Single 最大工作温度: 安装风格:Through Hole 封装 / 箱体:Max247 封装:Tube
SI4435DYPBF 功能描述:MOSFET 1 P-CH -30V HEXFET 20mOhms 40nC RoHS:否 制造商:STMicroelectronics 晶体管极性:N-Channel 汲极/源极击穿电压:650 V 闸/源击穿电压:25 V 漏极连续电流:130 A 电阻汲极/源极 RDS（导通）:0.014 Ohms 配置:Single 最大工作温度: 安装风格:Through Hole 封装 / 箱体:Max247 封装:Tube
SI4435DYPBF 制造商:International Rectifier 功能描述:MOSFET ((NW))